Guides · · Sebastian Correa
Window and Door Handing: How to Catch Errors in Takeoff
LH or RH, inside or outside: reading handing the same way on every plan set.

Handing tells the factory which side a window or door is hinged on and which way it opens. On most sets you read it from the swing lines on the plans and elevations, because the schedule line often leaves it out. In my experience, the two traps are mirrored layouts and reading the convention from the wrong side.
So check every operable unit before the quote goes out, and write down which side you read it from. The rest of this guide covers where handing shows up in a plan set, the conventions that disagree with each other, why mirrored units break the count, and a three-step check you can run on any job.
What is handing on a window or door?
Every operable unit has a hinge side, a fixed edge it pivots on. Handing names that side. A casement hinged on the left is left-hand. A swing door with its hinges on the right is right-hand. Sliding units have no hinge, so their handing names which panel moves.
It sounds like a small field. One window supplier's mulled-window guide puts it in five words: "Handing is the one people forget." The same guide adds that "a left-hand casement and a right-hand casement look identical on a napkin sketch and completely different on the wall" (Clad Wood Windows).
Operation and handing travel together. Operation says how a unit opens: casement, awning, hung, slider, fixed. Handing says which way. A takeoff needs both for every unit, which is why both appear in the fenestration takeoff checklist.
Where does handing show up in a plan set?
Three places, and they rarely carry the same amount of detail.
- Elevations. Casements and awnings carry a dashed V on the sash. The point of the V, where the two lines meet, sits on the hinged edge (CADBlockDWG). On an exterior elevation, a V with its point on the left means hinged on the left as seen from outside.
- Floor plans. Doors show their swing as an arc from the hinge. Casements sometimes show a small swing on plan too.
- The schedule. Some schedules have a handing column. Many only give type, size and operation, so the handing has to come from the drawings.
The elevation is usually the most reliable source, with one catch. Exterior elevations are drawn as seen from outside, and interior elevations as seen from inside the room. The same casement can show its V on the left on one sheet and on the right on another, and both are correct (CADBlockDWG). Before you read a single unit, find out which view the sheet uses.
When the schedule and the elevation disagree on handing, treat it like any other conflict between the two documents. The schedule vs. elevations guide covers which one wins and when to send an RFI.
Inside or outside: which side do you read handing from?
There is no single answer across the industry. That is the whole problem.
Windows. Large US manufacturers publish their own rule, and the rules are not always the same viewpoint. One manufacturer's help center says it hands all windows and patio doors from the exterior, and that if you look from inside, the reference reverses (Andersen). Another manufacturer's casement guide sets hinge handing from the exterior, then names the operator handing by where the lock sits as viewed from the interior (JELD-WEN casement product guide). Two viewpoints in one document, for two different parts.
Sliding patio doors. One manufacturer's ordering guide requires every patio door to be described "Outside Looking In" (United Window & Door). Sliders are usually written as X for the moving panel and O for the fixed one, so XO and OX are mirror images, and they swap if you read from the wrong side.
Swing doors. US door hardware uses a different test. Stand on the secure side, the side where the key goes, and look at the hinges. Hinges on the left and the door swinging away from you is left hand (LH). Swinging toward you makes it left hand reverse (LHR). The same logic gives RH and RHR (I Dig Hardware, Allegion).
European doors. A door hardware maker writing for export buyers points out that the European method stands on the side the door opens toward, while the American method (ANSI/BHMA A156.115) stands outside. "The same physical door is DIN-left under one and right hand under the other" (Canton Lock). If you buy from or sell to European factories, that sentence is worth printing.
The practical rule follows from all of this. Write the convention on the quote, next to the handing. "LH, viewed from exterior" survives a phone call. "LH" alone is a guess about what the reader assumes.
| Type | Where it shows on the plans | Convention to state | Typical error |
|---|---|---|---|
| Casement | Dashed V on the elevation, point on the hinge side | Viewed from exterior or interior, plus the factory's own rule | Reading an interior elevation as if it were exterior |
| Awning | Dashed V on the elevation, point at the top | Hinged at the top; check whether the factory hands any hardware | Assuming no handing field is needed for the hardware |
| Sliding door or window | Arrow on the moving panel; XO or OX in the schedule | X = moving panel, O = fixed, viewed from outside unless noted | XO read from inside and ordered as OX |
| Swing door | Swing arc on the floor plan | LH, RH, LHR or RHR from the secure side | Mixing the European and US conventions |
| Door pair (French doors) | Two arcs on the plan, one active leaf | Hand the active leaf (the one with the lockset) | Handing the inactive leaf |
The door pair row comes from the same door hardware guidance: for pairs, you hand the active leaf, the one with the lockset (I Dig Hardware).
Why do mirrored units break the count?
Multifamily and townhouse sets often draw one unit plan and mark the next unit as mirrored. Every window and door in the mirrored unit flips its handing. The schedule mark usually stays the same.
Take a simple example. A building has 12 apartments: 6 drawn as Unit A and 6 noted as "Unit A, mirror." Each apartment has two casements marked W-2. The schedule lists W-2 with a quantity of 24 and no handing column. A takeoff that copies the handing from the one drawn unit orders 24 casements with the same hand. Twelve of them are wrong.
Nothing on the schedule warns you. The only signal is the word "mirror" on the plan or a note in the unit key. So when you see a mirrored unit, split every operable mark into two lines, one per hand, before you count. The guide to counting windows and doors from PDF drawings covers where else typicals and repeats hide.
How does handing work on mulled units?
A mulled unit is two or more windows joined into one frame assembly. Each unit in the assembly keeps its own operation and handing. A pair of casements mulled side by side can be two left-hands, two right-hands or one of each, and only the drawings can tell you which.
The same supplier guide is direct about how to order these: "Specify each unit in the assembly separately. Operation, size, handing and glass." On sizes, it warns: "If you only give unit sizes, someone has to do the math, and that's where errors creep in" (Clad Wood Windows). Treat handing the same way. One line per unit in the mull, each with its own hand.
What does a handing mistake cost?
There is no public number for the cost of a wrong-handed window, and I would rather not invent one. What the trade does say about wrong orders in general points the same way.
A window is built to order, so a wrong one may not go back on the shelf. In one contractor thread about a wrong window order, one commenter put it bluntly: "No such thing as crediting back a mismeasure." Another said that with a good relationship, the lumber yard reps would likely credit it (r/Construction). In another thread, about windows ordered at the wrong size, a contractor estimated that returning them would take "another two weeks" and cost "a $3000.00 + mistake" (ContractorTalk). That case was about size. A wrong hand goes through the same reorder: same unit, built again, waiting again.
A reversed hand is also hard to spot before installation. Size, glass and color are all correct. Only the side it opens from is wrong.
A three-step handing check before the quote goes out
Run this on every job, after the count and before pricing.
- Every operable unit has a hand. Casements, sliders, swing doors and door pairs each carry a hand on the takeoff. Fixed units carry the word "fixed," so a blank never means "not checked yet."
- Every hand has a viewpoint. Write exterior or interior, or the secure side for doors, next to the hand. Check it against the manufacturer you are quoting, since their rule decides what they build.
- Every mirrored unit is split. Any mark that appears in a mirrored unit gets two lines, one per hand, with its own quantity. Add them up and check the total against the schedule quantity.
If a hand cannot be read from the drawings, ask by RFI. A one-line question costs a day. A unit hinged on the wrong side gets built twice.
This check also catches revision problems. A revised elevation can flip a hand without touching the schedule, so after an addendum, rerun step 1 on the units that changed.
FAQ
Is a left-hand casement hinged on the left from outside or from inside?
It depends on the manufacturer's convention. The two large US manufacturer guides cited above set casement hinge handing from the exterior, so a left-hand casement is hinged on the left when you stand outside. One of them names operator hardware from the interior. Write the viewpoint next to the hand on every quote.
Does handing apply to sliding doors?
Yes. A sliding door has no hinge, so its handing names which panel moves. It is usually written as XO or OX, where X is the operating panel and O is the fixed one, viewed from outside unless the set says otherwise.
How do I show handing on a quote?
Give every operable unit a hand and a viewpoint, for example "LH, viewed from exterior." For swing doors, use LH, RH, LHR or RHR from the secure side. Split mirrored units into separate lines, and give each unit in a mulled assembly its own hand.
Why do mirrored floor plans cause handing errors?
A mirrored unit flips the handing of every operable window and door, but the schedule mark usually stays the same. If the takeoff copies the hand from the drawn unit, half of those units are ordered with the wrong hand.
Wondering what this means for your team? Get your numbers in a 60-second fit check.